You are here: Home > Water Methanol Injection
Sort By:
Page of 1
Eurodyne Boost Manager With pump and nozzle
Our Price: $749.00

As a more streetable and cost effective solution to race gas, water-methanol injection allows people with wanting to turn up the boost to do so without spending $15+ per gallon using race gasoline. By lowering charge air temperatures, water-methanol injection allows the end user to run more timing and boost pressures. The Eurodyne boost manager is a full laptop programmable table. Unlike other systems where you have two screws for start and max boost, the boost manager allows you to precisely plot methanol injection amounts based off of charge pressure and rpm. The typical inferior twin dial adjustable boxes leave much to be desired especially on cars that don't make max boost at max rpm, you can find yourself botching the mid range to keep the meth 100% on in the higher rpm. With this system you can accurately calculate your water meth flow just as accurately as you can control your fuel injector or timing tables in a standalone ecu.
Snow Performance stage 1
Our Price: $350.00

The Snow Performance Stage 1 Boost Cooler® water-methanol injection kit
is available for all forced induction applications
(supercharged/turbocharged). Operation is simple and reliable: the
system starts injecting when the boost switch reaches the
user-adjustable point and injects a fixed amount of fluid through the
nozzle until boost goes below the set switch point. Proven to deliver
30-70 HP increases to all forced induction applications!

This makes it a good choice for low to medium boost setups (1-15 PSI)
looking for an octane enhancement and cooler intake charge. Activation
can also be set up through any other user-chosen switch, such as a full
throttle switch, nitrous switch, etc.

*Kit Includes:*
* 300 PSI UHO (Ultra High Output) Pump
* 3 Quart Reservoir
* All Tubing Necessary for Installation
       10' ¼ Inch High Temp Nylon Tubing
       18" High pressure Boost Line
       3' (Black) Wire Loom
* Boost Switch (1-15 PSI)
* Pig Tail Harness
* Level Switch Upgrade
* 1 Nozzle Holder/Check Valve Combo
* 3 Hyper-Sonic™ Nozzles (175, 375, 625 ml/min) For Applications up to
1,000 HP (for custom nozzle selection give us a call at 719-633-3811)
* Required Hardware Needed For Installation
* Snow Performance Running S Decal
* Comprehensive Instructions to Install on Any Forced Induction Vehicle
* Snow Performance 1-Year Warranty
Snow Performance stage 2
Our Price: $385.00

Unlock 50-70HP on your boosted vehicle while decreasing your air temps by up to 150 degrees! The Snow Performance Stage 2 Boost Cooler® water-methanol injection system is available for all forced induction (supercharged/turbocharged) vehicles and uses a progressive controller that proportionally injects more or less according to boost pressure. Start and full points are adjustable for engagement and delivery curve to match what the engine requires. Proportionally injecting according to boost pressure gives an accurate delivery of water-methanol and allows cooling and performance improvements over a wide range for improved drivability. Proven to deliver 50-70 HP and reduce inlet temps by up to 150 degrees! The Stage 2 comes with a VC-20 (1-20 PSI) controller that can be mounted anywhere in the engine bay or cab for a clean install and comes with the industry leading Snow Performance 300 PSI UHO pump and Hypersonic Nozzles™ for the absolute best atomization and power available for your forced induction vehicle. *Kit Includes:* * 300 PSI UHO (Ultra High Output) Pump * 3 Quart Reservoir * All Tubing Necessary for Installation 10' ¼ Inch High Temp Nylon Tubing 18" High pressure Boost Line 3' (Black) Wire Loom * Progressive VC-20 Controller * 3 Wire Harness * Level Switch Upgrade * 1 Nozzle Holder/Check Valve Combo * 3 Hyper-Sonic™ Nozzles (175, 375, 625 ml/min) For Applications up to 1,000 HP (custom nozzles avaialble) * Required Hardware Needed For Installation * Snow Performance Running S Decal * Comprehensive Instructions to Install on Any Forced Induction Vehicle * Snow Performance 1-Year Warranty *NOTE:* For use with all centrifugal superchargers (ProCharger, Vortech) and large turbos. For positive displacement superchargers (Eaton, Twin Screw) and small fast spooling turbos see (part# 212) Stage 2 MAF/MAP for best performance.

Snow Performance stage 3
Our Price: $750.00

The Snow Performance Stage 3 Boost Cooler® is the most advanced
water-methanol injection system for your EFI (electronic fuel injected)
and forced induction (turbocharged/supercharged) vehicle. The Stage 3
creates a 2D injection map based off boost and fuel injector pulse width
to deliver the most accurate and tunable water-meth delivery on the
market.

Taking it one step further the Stage 3 will control 2 Hyper-Sonic™
Nozzles independently of one another to solidly the exact amount of
water-methanol is provided at all rpm ranges of the engine. This 2D map
injection and dual stage technology translates into the most accurate
injection curve and tuneability of any water-methanol system giving
50-110 HP gains and up to 150 degree reduction in air temps! Tie this in
with the industry leading Snow Performance 300 PSI UHO pump, Hypersonic
Nozzles™, and terminated weather tight OEM harnessed wiring connections
and the Stage 3 promises to be the easiest and most effective
water-methanol system on the market for your EFI and boosted vehicle.

*Kit includes:*
* 300 PSI UHO (Ultra High Output) Pump
* 3 Qt Reservoir
* All Tubing Necessary for Installation
       10' ¼ Inch High Temp Nylon Tubing
       18" High pressure Boost Line
* Terminated Digital Variable Mapping Controller
* Terminated Plug&Play Wire Harness
* Power Solenoid Upgrade
* Level Switch Upgrade
* 2 Nozzle Holder/Check Valve Combo
* 3 Hyper-Sonic™ Nozzles
* Snow Performance Running S Decal
* Required Hardware Needed For Installation
* Comprehensive Instructions to Install on any EFI/Boosted Vehicle
* Snow Performance 1-Year Warranty